Dong Fang DF 250 RTB Bobber Information

Quote:

---

Originally Posted by DanDaMan

I put a 36 on and 4th hits what 5th used to

5th used to top out max revs at 70 , 4th now pushes to 65-70

so instead of a screaming engine on highway , it almost a growl / heavy purr

---

All this info from everyone has been great. I just have yet to decide what i am gonna do. The inserts in the hub are a tad smaller than the threaded end of the stud.So the bolt holes on the sprocket are slightly bigger,and if i find something to fit into the the inserts in the hub..then the size is too small for the sprocket and will cause issues later. If I remove the inserts,then I have a big hole to deal with.Putting a heli-coil in the inserts only brings me to a smaller bolt for the sprocket... Plus I am thinking too hard on this..and my mind is numb.
Dan- a link to where you got your sprocket would be great..I figure since I already have this apart ..I should get the sprocket now.I like the way yours sounds like it turned out.
Maybe then i can figure out about the studs and go with that. I may just go ahead and order the studs from scooter depot today.. and hopefully get them within a decent enough time.But at the same time order a 36 tooth sprocket while I am at it.

Barnone's link for sprockets http://www.oldbikebarn.com/Motorcycl...?search=JTR279 ---- model number jtr279.35

I have a 428 DiD chain I got the sprocket for it from http://www.rebelgears.com/pricelist.html , while yours came with a 520 stock chain so you need the 520 sprocket

old bike barns cheaper , but didnt have the 35/36 tooth 428 : \


oh ya , get yerself a few strippers http://www.boltdepot.com/Shoulder_bolts.aspx?nv=l the larger shoulders than threads fill the sprocket holes , you would prob have to carry the sprocket and insert u intend to use into store for sizing

Quote:

---

Originally Posted by DanDaMan

Barnone's link for sprockets http://www.oldbikebarn.com/Motorcycl...?search=JTR279 ---- model number jtr279.35

I have a 428 DiD chain I got the sprocket for it from http://www.rebelgears.com/pricelist.html , while yours came with a 520 stock chain so you need the 520 sprocket

old bike barns cheaper , but didnt have the 35/36 tooth 428 : \


oh ya , get yerself a few strippers http://www.boltdepot.com/Shoulder_bolts.aspx?nv=l the larger shoulders than threads fill the sprocket holes , you would prob have to carry the sprocket and insert u intend to use into store for sizing

---

Dan you ARE the Man.. thank you thank you thank you!!!!!!!!!!:thumbsup:

Trying out my new camera on the DF250TRB

http://s1229.photobucket.com/albums/...t=Untitled.mp4

I want to gear up my d250rtc. So the Honda Rebel, etc sprockets fit these?

http://www.oldbikebarn.com/JT-Rear-S...9-35T-35-Tooth

Thanks

yup the bike is really a honda clone , right down to bolt patterns , with just minor frame adjustments to make about 5 diff style bikes

I would even bet the little rebel 250cc twin motor would bolt right in , or even the fuel injected CBR250R motor

Found the df250rtb on this site for $1895.00

I own one but thought it was a good deal if anyone was interested. No, no affiliation.

http://expressatvs.com/proddetail.as...linenumber=622

Site is slow to load?


Here's mine.

Attachment 7087

Hi all! New here, Have read every page and am this close to ordering a DF. The expressatvs after adding shipping and 3 more months warranty ends up pretty much the same as everyone else- or higher. Found one here:

http://www.mygokarts.com/250cc-manua...e-mc-df250rtb/

for $1919 free shipping but I haven't been able to verify the site.

Anyway, love all the posts! But I am a little peeved all of barnone's pics are gone! Why delete all the pictures grrr! I just haven't decided whether to go with the DF or buy a used Honda Rebel for $900 locally. Decisions, decisions.

Best, Xeta

I bought a DF250rtc from ScooterGasMotor.com and I have no complaints. It was $1759 + shipping, extra warranty, shipping ins = $2236 Total.

The one they have listed is a JinLun JL250p, but they ended up shipping me a DongFang 250rtc instead after confirming the shipping change with me, which ended up being a good thing since for whatever reason the JinLun is not able to be licensed in FL.

Contact: "Jason @ SGM" <scootergasmotor1@gmail.com> if you are interested.

Word of advice: When doing final assembly out of crate, go through bike thoroughly and make sure ALL bolts are tight and use blue loctite at your discretion, and check fuel lines, brake lines, and vacuum hoses for kinks. The QC on Chinese bikes isn't the greatest.

Beware of some of the sites listing very cheap and make sure they aren't trying to scam you, asking for money order payment.

I just realized after writing all this that you were looking for the bobber model not the sport model :\

Hi.everyone im new to the site been great thread on the dong fang bobber,been thinking about buying one,anyone know if this bike can be registered in bronx,new york?i called my dmv but they said i need the vin number for them to look it up.also wish the guy's name was something better then dong.... lol,keep up the great post hope to hear/see how the bikes are holding up,someone take some video's of it please youtube only got like 3 video's on this bike would like to see some videos from the buyer's!