Adventure Motorcycle Magazine Subscribe Now

Search:

Type: Posts; User: chamjiee

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. These are the wires coming off of my rectifier...

    These are the wires coming off of my rectifier regulator.

    What pa the black cable for?

    Can I connect any yellow wire from stator to any yellow wire from the regulator as I do not have the...
  2. Worrying the three phase stator to a rectifier

    Hi
    I have swapped engine in my bike and me engine is dc cdi and it's stator has 12 poles coils.
    It had 3 wires coming from its stator yellow color and two words from the pulsar coil. The yellow...
  3. Re: Convert water cooled engine to air cooled ( 163MM TO 163FML)

    [QUOTE=humanbeing;89996]
    please if you can guide
  4. Re: Convert water cooled engine to air cooled ( 163MM TO 163FML)

    Bump @humanbeing
  5. Re: how to wire Engine kill switch with dc cdi

    Any idea
  6. how to wire Engine kill switch with dc cdi

    hi
    i have swapped engine in my bike. stock egngine was ohv 125 cc ac cdi.
    new engine is 250cc ohc with dc cdi.

    how to wire the engine kill siwtch in the right handle grip with this cdi ?
    ...
  7. Which center packing is correct for horizontal engine

    Hi
    During bottom end rebuid of second engine i noticed that the center gasket had a cut behind the oil filter screen place.

    I remember my first engine rebuild there was no such cut as shown in...
  8. Bog down and hesitation after installing performance camshaft

    Hi
    I have installed a performance camshaft in a Chinese clone of Honda 70cc engine.
    The can shaft has high lift lobes.

    It bogs down after half throttle and seems as if timing is advanced.

    Cdi...
  9. Ideal operating temperature range for cg200 liquid cooled

    Hi

    What is the ideal temperature range measured by the temp sensor installed in the radiator of a liquid cooled 200cc Ohv water cooled engine 163ML?

    Mine is running at 80-100C.

    Here...
  10. Anyone swaped had cylinder block from 163ml air...

    Anyone swaped had cylinder block from 163ml air cooled to water cooled one?

    Sent from my Nexus 5 using Tapatalk
  11. Thanks is it using same engine mounts as cg125...

    Thanks is it using same engine mounts as cg125 /cg200 163ml?

    I would like to replace this engine with single cylinder liquid cooled one.

    Sent from my Nexus 5 using Tapatalk
  12. Yes zxmco is local distributor that imports and...

    Yes zxmco is local distributor that imports and sells and then shows its ar$3 when it comes to support. The only thing that I m sure about it is that is lifan product.
    Does it comes with single...
  13. Need to id this bike and engine specifically

    Hi

    Any one who can help me id this bike?
    It's 250cc apparently.
    Need to know it's specs and need some other engine parts for top end work...
  14. Thanks I resolved it. Seems like the idle ...

    Thanks I resolved it. Seems like the idle adjustment screw was out too much.. Don't know how that happened as just removed the carb and manifold from head and immediately installed on the 200cc non...
  15. This can't be die to too much fuel. As the carb...

    This can't be die to too much fuel. As the carb is from a 125cc engine. No serious jetting is done on it. Except that a big bore was installed on 125to male that 150cc and this carb was running...
  16. Yes it not perfect size. But why is it starting...

    Yes it not perfect size. But why is it starting only and only if that nozzle is opened?

    My understand is that that nozzle will further lean the air fuel mixture leaving the carb. And hence...
  17. Bike only starts if Carburetor insulator nozzle is open

    Hi
    I had a Chinese 125cc ohv engine. It had some euro 2 standard device setup. There was an air pipe going from the carburetor intake manifold insulator to that euro 2 device.
    I swapped the engine...
  18. Replies
    0
    Views
    1,931

    Help me identify below engine

    What is this engine from need its specs. As per seller it could be 150cc.no more details...
  19. Replies
    2
    Views
    1,550

    Not a shop can't build that system or buy it. ...

    Not a shop can't build that system or buy it.

    I will order replacement item. But don't know which one should I suspect?

    Sent from my Nexus 5 using Tapatalk
  20. Replies
    2
    Views
    1,550

    1p54fmi stator resistance is it normal?

    Hi I have 1p54fmi. No spark problem.

    Checked the resistance of primary side of ignition coil its 0.6ohm. Secondary coil resistance is 4.7k ohm.

    Stator high tension coil resistance is 425ohm....
  21. Which ignition coil is best among below two?

    Hi

    I have lifan 1p54fmi 124cc 54mm square bore engine with big valves.

    How do I know which ignition could is best for it?

    One coil is from 85cc bikes produced locally it's primary winding...
  22. Need speedometer odometer tripmeter plastic gear

    Hi

    I need this plastic gear or whatever it is called.
    The meter is working fine only the odometer and trip meter aren't incrementing. This is because the teeth on the long shaft gear are chewed...
  23. Convert water cooled engine to air cooled ( 163MM TO 163FML)

    Aoa,
    I have 163ML engine. It's water cooled at the moment. I want to convert it to air cooled. I m of the view that replacing only head and cylinder and removing water impeller and shaft will do the...
  24. Replies
    50
    Views
    97,879

    Sticky: Brands is missing name if Chinese bikes brands ...

    Brands is missing name if Chinese bikes brands

    Sent from my Nexus 5 using Tapatalk
  25. Replies
    50
    Views
    97,879

    Sticky: Gear shift drum? Sent from my Nexus 5 using...

    Gear shift drum?


    Sent from my Nexus 5 using Tapatalk
Results 1 to 25 of 28
Page 1 of 2 1 2