Search:

Loose gear shifter lever.

I tried to tighten it up but it was still loose.

Wrapped some electrical tape around the shifter shaft, put the shifter lever back on, and tightened it down.
...

No problems at all shifting from 1st to neutral.

I took a look at the shifting lever a few minutes ago and notice that it was very loose.

I tightened it up and adjusted the clutch cable. (at...

I'm at a stop light in first gear.
The light changes.
I take off in first gear.
I pull the clutch, I pull the gear lever up as much as I can with my foot and the bike won't shift into second.
I...

thank you all for the info. i really appreciate it.

I have a 2008 xf200 and am looking to buy parts and tools for my bike. I noticed that there are a bunch of readily available (and very inexpensive!) parts on taobao.com for the qingqi gm200. (which...

How's it going? I live in north Miami beach and work in Hollywood. I ride a qlink xf200. I bout it used with 50,000 miles on from a guy who mistreated the bike. Even though the previous owner beat it...

Just found this!

http://www.ebay.com/itm/Qlink-XF200-XP200-Sprocket-Counter-SSR-Motorsports-Enduro-/181001709009?

thanks humanbeing.

are you sure that this http://item.taobao.com/item.htm?id=19323176869 flywheel removal tool will work for the xf200? it looks nothing like any of the tools shown in the manual...

Here are some pictures from the xf200 manual of the tools needed to pull the flywheel.

9333

*foot in mouth*

You are absolutely right MJH, I was mistaken. The manual mentioned replacing the fuel lines every 4 years which just so happened to be right below the cam chain adjustment topic.
...

WOW! can the flywheel on the xf200 be removed the same way as the guy in the video above removed his? is a flywheel puller even needed?

thanks humanbeing.ab
my biggest concern with option 1 is aquiring the correct flywheel puller. does anyone know where to find one or how to go about figuring out which puller i need?

What a relief! Thanks ChinaV!

That's exactly what I saw, a coating of oil on the flywheel.

After about 5-10 minutes of removing the 17mm hex cap that allows you rotate the engine, I noticed...

Will the 16t front sprocket for the sinnis apache qm 125 gy fit a 2008 qlink xf200?

I looked on Dennis kirk and sprocket specialists and the 16t sprockets mentioned on this thread are no longer...

Thanks Zorge. I figure someone here should know if this is normal and if not, what needs to be replaced.

Enough for oily to slowly leak from where the lowest yellow cap is when it's removed
http://www.contactdi.com/2008/fix/fix005.jpg

I couldn't tell you exactly how much oil is in the cover. All I...

Here's a link to a video of Option 2 above.

If I go this route, I'll use a chain break to break the chain and a chain riveter to put the chain back together.
...

Nice cam chain tension adjustment video.

http://www.youtube.com/watch?v=QUvPp96hpXc

It's time to replace the cam chain on my bike.
According to the manual, the cam chain is supposed to be replaced every 4 years.

I've been watching videos on YouTube on how this is done as well as...

Hi everybody. When preparing to adjust my valve clearances on my 2008 qlink cf200 the other day, as I was string the motor to tdc, I noticed that there was a considerable amount of oil inside the...

Do you have a picture showing such vaccum line needed to be replaced? I'm have the same issue. I decided to break the rubber seal on the gas cap for a temporary fix which isn't good in the long run...

Thanks humanbeing. Great PDF!

How does k157 suggest that it's like the 125? Where are you getting this information from?

Yes Zorge, 50,000. The bike has very good compression and starts in one or two kicks every time. Granted, it needs a little bit of work but very much worth the $400. The previous owner rode the q...

http://www.contactdi.com/2008/fix/clutch005.jpg

I just bought a 2008 xf200 with 50k miles on it about a month ago for $400 and it is running pretty good. The bike is leaking oil from the clutch...