Search:
Type: Posts; User: nimbus
Search: Search took 0.00 seconds.
-
08-02-2010, 01:57 PM
Thread: QLink/QingQi rack...cause Carl asked me to
by nimbus- Replies
- 46
- Views
- 50,391
Re: QLink/QingQi rack...cause Carl asked me to
I too bought one of these racks from Carl (he's da man). Anyhoo, I used all the same bolts to install. It took a few minutes to figure out the tail lights but all went together in about 20 minutes....
-
08-02-2010, 01:43 PM
- Replies
- 62
- Views
- 86,235
Re: Programmable CDI Qingqi QM200 (Qlink, STX, Sinnis, etc)
I would say it would worthwhile if you have aftermarket exhaust and rejetting but for a stock setup I wouldn't bother. I have both and tested the CDI on both.
-
04-11-2010, 01:45 AM
- Replies
- 2
- Views
- 5,816
Re: Carb woes - This should be an easy one! Please help.
It was the same main that came with the bike. In any case my neighbor dropped by today and looked at it. So turning the needle jet to align with the pin so that I could thread the main jet was the...
-
04-10-2010, 02:00 AM
- Replies
- 2
- Views
- 5,816
Carb woes - This should be an easy one! Please help.
Ok so here's the deal. I have the Qlink XF200 with Mikuni BST 28 carb. I am not a carb expert by any stretch.
I went to change out the main jet but once I got the main jet off I couldn't get it... -
04-07-2010, 03:04 AM
Thread: Qlink XF200 Carb questions
by nimbus- Replies
- 3
- Views
- 8,264
Re: Qlink XF200 Carb questions
Yeah that's pretty much my theory at this point. I'm going to check the needle tomorrow. Any ideas on why the main jet won't feed into the threads with the washer on? I hope when I open the top I can...
-
04-06-2010, 10:28 PM
Thread: Qlink XF200 Carb questions
by nimbus- Replies
- 3
- Views
- 8,264
Qlink XF200 Carb questions
I have a XF200 I purchased used (with 200km on it). The person who
originally bought it installed a FMF Turbine Core 2 exhaust on it. The
bike runs rich and bogs only at full throttle and fouls out... -
12-02-2009, 04:06 AM
- Replies
- 62
- Views
- 86,235
Re: Performance CDI for Qingqi QM200GY (Qlink XF200, STX, etc)
Yeah I hope reliability won't be an issue if my brain is engaged. You don't use synth until the engine is well worn in if at all and yeah the high revs probably would cause issues. I vary my speeds...
-
11-30-2009, 08:34 PM
- Replies
- 62
- Views
- 86,235
Re: Performance CDI for Qingqi QM200GY (Qlink XF200, STX, etc)
I don't have too many miles since I installed the CDI on my XP200 but reliability seems to be the same. The revs do tend to be smoother with the new CDI and the bike top speed seemed to increase a...
-
10-24-2009, 09:17 PM
- Replies
- 62
- Views
- 86,235
Re: Performance CDI for Qingqi QM200GY (Qlink XF200, STX, etc)
Thank you forchetto!
I bought one so I'll let you all know what I think -
10-24-2009, 02:12 AM
- Replies
- 62
- Views
- 86,235
Re: Performance CDI for Qingqi QM200GY (Qlink XF200, STX, etc)
Hey guys I noticed Xian racing has the Kamakazi 200 CDI for $29.99 Pounds right now. With shipping to U.S. it came to $64. Woohoo!
...
Results 1 to 10 of 10
The Pillars of Salubrity:...
Yesterday, 12:12 PM in Off Topic Discussions