Search:

Glad you were not hurt either. CFMOTO Australia are replacing both side plates under warranty. It appears the replacements are stronger than the originals. This pleases me because i did not want a...

Glad you also survived. Sounds like the new G has a different peg position so i wonder if the castings are interchangeable on the tr.

My left hand foot peg broke away from the side casting causing a low speed drop down.

I was just shifting my position when the foot peg broke off causing my foot to hit the ground loosing control....

The first batch of 650TK we got in OZ had the medium screen so I added the MRA spoiler to the screen which made it work like the taller screen like you get elsewhere (see above posts). I managed to...

Hi. I got the first 650tk in Tasmania and love it. Added lots see ghe posts. Australian service and support via dealers is what we expect in Australia. Great value for money if you want a good...

They are there. it is a lug under the arm. Threaded ready for a bobbin. with my paddock stand I found the handle too ehort and it was too heavy to lift us8ng the bobbins so I use the L padded...

I have a Shad 35 and just by luck the red matches perfectly. It comes with a mounting plate but the holes do not line up so I had to drill the 650TK plate using the Shad plate as a guide. Very easy....

most bikes will not start in gear if the side stand is down. Put side stand up clutch in and it will start in gear or if neutral light is off.

Added - I use a rear paddock stand to service the chain etc but I also have a front wheel stand which I ride into to lock the bike upright with no need to use the side stand at all.

This stand...

Hi Michael,

Good to see a fellow Australian on board.

Cheers, Rob

I bought my HIDs in Australia but like everything else they were made in China. The fast start ballasts are new, they were recomeded to me after I said that I would only buy the low beam Hid and keep...

I took your advice biker doc and used 35W Hid low beam and 55W high BUT I used the new fast switching ballasts which have a much higher startup current 8 amps each so I had to conect the high beam...

I have not had any problems with ground clearance but it would depend on your riding. The pegs still fold up if you did touch down. Probably no good for the track. There are plenty of reviews for the...

I took the power from one of the fuses. Join into any 12volt wire that has power when the ignition is on. connect relay coil to this 12v supply snd the other side to ground. Connect 12v direct from...

I have emailed 2 companies who make the risers for the ST1300 asking for bolt pattern specs but have not had a reply. The risers are expensive so I am not prepared to buy them and hope they may fit....

Some people, including myself, find the 650TK riding position cramped. I feel like my top half is in the upright touring position , legs sport bike and bum somewhere in-between. I shopped around and...

I found an after market radiator mesh guard made specifically for the new CF650 in Australia. http://www.radguard.com.au/

Simple to install, remove plastic guard under the radiator (4 screws),...

Bikerdoc - does the increased angle make much difference with the higher screen you put on or is it just better for fitting your gear under it. My screen spoiler extension is adjustable but I...

I think they stole that screen from the Riot Police.

In OZ we get the medium height screen which I find pretty good most of the time.. We do not get dirty air like some places in China so I prefer to get some air at chest to visor level in warm to hot...

The LEDS come with a typical basic bracket which I attached to the front wheel guard using the rear bolt. The bolt is rubber mounted which worked great, just remove the bolt, place the bracket and...

IMHO this mod is the best single safety enhancement you can make to your ride and should be standard on all street bikes. We all know that visibility is the biggest risk we have while out on the...

More info on my brake light flasher.

I bought it on e-bay from china for about $4US. It is called GS-100A Strobe Controller for LED stoplight. You simply splice it in line with the stoplight...

I have been told by a CFMoto official in Oz and my CFMoto mechanic and have seen a few comments on the net that the throttle restriction is on the injector body. It is a simple bracket with 1 screw....

The side stand used on the CF650 is far too short making it heavy to stand up and at least some (if not all) have far too much slop in the joint. My bike slips 75mm due to the slop until it settles...