Results 5,751 to 5,760 of 6336
|
-
#5751 Re: Look out below......04-18-2016, 06:49 PM
Yep, emergency cable repair kit. Got one in my tool bag on the DF. Never used it yet!
http://www.amazon.com/KiWAV-Universa...=sr_1_1&sr=8-1
Vince
2021 Ural cT
2022 Dong Fang DF250RTG
2021 Ice Bear 150cc scooter
2020 Ice Bear 150cc Scooter
-
#5752 Re: Dong Fang DF 250 RTB Bobber Information04-18-2016, 09:05 PM
fwiw the same or similar cable kit on ebay (ie save over 50%)
also the magnet wire i bought to rewind the stator (before i found the separation with the lead wire and just fixed it)Last edited by axa; 04-18-2016 at 09:30 PM.
2012 DF250RTB_B with Yamaha XV250 V-twin
1998 XVS650 (For Sale)
2003 LS650 with Voodoo Vintage hardtail
-
#5753 neutral sensor04-18-2016, 10:03 PM
One thing to note and notice, when taking off your front sprocket cover for any reason, be careful how you put it back, it is real easy (ive apprently done it at least twice) to pinch the neutral sensor wire.
No wonder it wasnt working, well i had enough slack to solder a new lead but if you don't or cant solder, you might have some trouble finding the correct replacement.
Ive only come across one that looked right, from Europe and it was used and expensive.
The correct stator wasn't exactly cheap and a bit hard to find also.\
But if youve followed my rant, Ive said nothing was so hard to find as was engine rods...
most people will find themselves better off tossing out the entire bike than dealing with a problem that effects the rods2012 DF250RTB_B with Yamaha XV250 V-twin
1998 XVS650 (For Sale)
2003 LS650 with Voodoo Vintage hardtail
-
#5754 stator work04-19-2016, 04:48 AM
When replacing the stator cover take note on the intermediate starter gear washers.
I had 2 on each side but needed to remove one as apparently reuse of the gasket caused this gear to be squeezed and not allow the starter to turn...
Almost caused me to buy a new starter...
-
#5755 Re: neutral sensor
-
#5756 Re: neutral sensor04-19-2016, 09:43 PM
-
#5757 Re: neutral sensor04-19-2016, 11:33 PM
You said" most people will find themselves better off tossing out the entire bike than dealing with a problem that effects the rods"
I say " buy a new engine and not throw out the entire bike"
Vince
2021 Ural cT
2022 Dong Fang DF250RTG
2021 Ice Bear 150cc scooter
2020 Ice Bear 150cc Scooter
-
#5758 Re: neutral sensor04-20-2016, 05:11 AM
Tuchè, so that was a bit facetious..., still I've yet to come across anyone with serious problems that gets their bike going again.
I've been contacted by 2 people with blown engines, both at least a year later still had dead bikes. No exaggeration there.
By the way I did finally stumble uponc 2 sets of rods, the first currently in use a steel set, made in China, free from an unamed dealer,
And a second set also steel but of questionable quality, from a guy on ebay in Bulgaria, 9$ shipped.
So it's been possible to resurrect this bike this far, just emmensly difficult to find all the parts.
Back to the topic at hand, turns out I do have a bad starter now if not before. Might have damaged it when I binded the starter intermittent gear.
I'll see if I can fix it too but...
It never seems to end.Last edited by axa; 04-20-2016 at 06:03 AM.
-
#5759 Starter motor brushes04-21-2016, 07:32 PM
So my starter motor brushes got pulverized during a hasty reassembling.
Can find a replacement set for about 20$, but can find an entire new starter for $30
Can anyone point me to a source for reasonably priced brushes?
http://www.alibaba.com/product-detail/Cg250-Free-Sample-Motorcycle-Starter-Carbon_60351400296.html
Update:
Screw it, for 29$ ill buy the entire new motor, and use the old one as Ive been wanting to modify it for kickstart a long long time...Last edited by axa; 04-22-2016 at 03:47 PM.
-
#5760 Re: Starter motor brushes
- Join Date
- Mar 2015
- Location
- ohio
- Posts
- 11
04-24-2016, 07:31 PMHey everyone so I have since put alot of miles on my Rtb 250-B, love this bike to death, however its time for an overhaul, so if you guys could help me out with links or ideas for possible parts thatd be great! So here is what I am looking at getting. I need new sprockets( suggestions for good torque and speed? I am thinking 13/35).
-I need new jets
-new front rim
-mettallic gas cap
-new turning signals
-new grips
-new headlight (seems to be fairly dim at night even with brights, so best bulb would be?)
-small rear seat pad
-footpegs?
my girl rides on the fender with me everywhere its a blast but want her to be a little more comfortable.
So if you guys could drop some links or possible advice on where to get these items thatd be great man!
« Previous Thread | Next Thread » |
Similar Threads
-
Help ID this customized chinese bobber please?
By fonzerelli in forum StreetReplies: 6Last Post: 01-16-2022, 01:39 AM -
DD350E-2 Bobber
By xacarrere in forum Manufacturers and ImportersReplies: 2Last Post: 08-28-2015, 12:03 PM -
Bobber Bikes
By Geronimo in forum SidecarsReplies: 12Last Post: 07-20-2011, 05:02 AM -
my 2nd 16 inch bobber
By Geronimo in forum SidecarsReplies: 3Last Post: 09-13-2010, 11:10 AM -
JH600B Information Wanted
By blazeafar in forum Welcome to MCM!Replies: 1Last Post: 04-29-2008, 12:38 PM
Tags for this Thread |
комедии 2024 онлайн...
04-23-2024, 02:09 AM in Off Topic Discussions