Thread: Qianjiang Motor
Results 271 to 275 of 275
|
-
#271 Re: Qianjiang Motor07-21-2017, 11:39 AM
924100323.jpg
I use Motul 5100 10w-40 runs decent, change every 3000km, i have reached 20,000km for a while... you need to change the factory oil quick, 1st change like 500km, it's crap they put it in.
but be really careful when replace the oil filter, contra to common sense, the hole must facing out... if you mix up oil flow direction, the result could be blown oil filter cap and possible more damage. so a pre warnning
I bough a few spare factory oil filter, both front and rear have rubber seal attached to.
Tag on package it is
-----------------
Name BJ250-15
part no. QJ172MM-A
-----------------
1838527697.jpg
this side must facing out!!!
837952677.jpg
300820192.jpg
after tape measuring, here is rough spec
--Length 39mm, 44mm (both side rubber seal thickness include)
--Diameter 45mm
TDLast edited by td_ref; 07-21-2017 at 02:40 PM. Reason: correct number
同志仍需努力
-
- Join Date
- Jul 2014
- Location
- Poland
- Posts
- 327
07-23-2017, 09:51 PMThanks a lot!
With the bike i had become one piece of filter hf131. The dimensions are the same, but it has no rubbers seal). Do you think that the 2017 engine has another mount of filter?
I haven't open the cap yet. Maybe i can use old seals to the new filter.
And one more question: if i buy a 1liter of oil, will it be ok? Or must i have the 1.25...in this case i must buy this time two liters.
-
#273 Re: Qianjiang Motor07-24-2017, 02:15 PM同志仍需努力
-
#274 Re: Qianjiang Motor
- Join Date
- Jul 2014
- Location
- Poland
- Posts
- 327
07-24-2017, 05:46 PMI am a journalist, i have riden on the first registered BN251 in Poland.
I fall in love after 600km...i buyed new one from the importer, not from dealer.
I suppose this is the second imported BN251 to Poland. They sell this model since two weeks.
So i must do the service alone, but i have warranty ( they trust me :-) ).
I changed today the oil, the HF131 filter fits, but i had to use the rubber seals from the oryginal one, no problem with that.
I have drained out 1250ml of old oil, and i puted the same amount.
You had right, the oil after 500 km was black, and thanks again for the tip with the filter direction.
-
07-24-2017, 08:21 PM
For eliminating the spongy brake I would consider a steelflex hose and also a brake fluid change including real good venting process. A friend of mine with a Benelli TRK 502 cured the same issue by that procedure successfully
Sent from my GN8003 using TapatalkSWM RS500R, R1200GS LC
« Previous Thread | Next Thread » |
Similar Threads
-
QianJiang 150-19A
By lobotomous in forum StreetReplies: 21Last Post: 09-01-2012, 07:16 AM -
CBF125 China motor???
By jonnyenglish in forum StreetReplies: 5Last Post: 08-01-2010, 04:46 PM -
Info on what motor it has
By kens in forum MaintenanceReplies: 6Last Post: 10-04-2009, 05:25 PM -
Modified CJ 750 24 hp SV motor
By Shanghaifingers in forum SidecarsReplies: 1Last Post: 02-20-2009, 04:02 AM -
hi fellow motor bikers
By Lago888 in forum Welcome to MCM!Replies: 5Last Post: 04-25-2008, 08:53 AM
Tags for this Thread |
MedSolutions: Finding Solutions to...
Today, 08:28 AM in Off Topic Discussions