Adventure Motorcycle Magazine Subscribe Now

Page 1 of 2 12 LastLast
Results 1 to 10 of 72

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1  
    Life Is Good! ChinaV's Avatar
    Join Date
    May 2008
    Location
    Guangdong, China
    Posts
    1,508
    Decided to take the plunge and do the valve adjustment this weekend. I took some notes and pictures so people can see it's really not that difficult. I'm fairly sure all the Chinese motorcycles use a rocker arm design. The benefits of this are lower manufacturing costs and easy adjustments. The downside being more frequent adjustments and accelerated wear on the guides due to lateral friction.



    The shim under bucket design that is found in most modern motorcycles requires less maintenance, but can be a real PITA because you need a set of shims and generally must remove the camshaft to perform the adjustments.



    I worked in a Suzuki dealership in the late 80's and early 90's. At that time, almost all Suzuki models were using the rocker arm adjuster. We performed a first service at 600 miles and the valve adjustment was part of that service. I would say about half the bikes serviced were out of spec. Suzuki usually recommended 4000-8000 miles between valve adjustments. After the initial adjustment, most of the bikes we serviced stayed within spec and rarely required further tweeking until they reached high mileage.

    I think it's safe to say that most people don't touch their valves for two reasons. #1 Shops charge an arm and a leg for it because it's very time consuming. #2 Noisy valves usually won't stop the bike from running, and most people ignore maintenance until they are stranded on the road.

    With that said, I think it's best if you perform an initial valve adjustment at 1000 kilometers and then check them every 5000 kilometers.

    So let's get started..... I always like to start with a clean bike before tearing her down and getting inside. You are going to have a few areas of your engine exposed during the process, any loose crud hanging around your engine could fall inside and really ruin your day. Also not a bad idea to use a work stand for this operation.

    Ain't She Purdy!



    I would recommend pulling the seat, side panels and tank off. It's not absolutely necessary, but it makes the process a lot easier. Now that she's naked, remove the spark plug and the four items marked in yellow in the following picture.
    #1 Front Valve Cover 17mm spanner
    #2 Rear Valve Cover 17mm spanner
    #3 Timing Mark Cover 17mm spanner
    #4 Small Engine Cap 10mm Allen Wrench



    Put your 17mm socket inside the hole, where the 10mm allan cap was, and rotate the engine around (counterclockwise) until you see a mark on the flywheel indicating Top Dead Center. Verify you are at Top Dead Center (TDC) by checking the position of the piston through the spark plug hole. If you got it right, you can grab one of the rockers and wiggle it a bit. Remember, this is a four stroke engine, the piston will be at TDC twice during the four strokes. This is what you should see through the inspection hole if you got it right.



    Now, let's have a look at one of the valves. This happens to be the intake valve, but it is identical to the exhaust valve.



    Here's some colour coding and explanations for you first timers.
    The first thing you need to understand is what we are adjusting here. At the bottom, you will see a Green part and a Red part. We are trying to measure and set the gap (space) between these two items. The Orange screw at the top is what you will turn to make the adjustment. The Blue nut keeps everything tight after you have made the adjustment. Pretty simple



    You will need a set of feeler gauges to measure the gap. First thing you want to do is check the current gap, maybe your valves don't need adjusting. Through CrazyCarl, we have learned that the correct specification is .06mm to .08mm for both the exhaust and intake ports. Take a .09mm gauge and slip it in. If it goes in, you're valves are too loose. Take a .06mm gauge and slip it in. If it doesn't go in, your valves are too tight.

    If you need to adjust them, loosen the nut and back the adjuster screw out. Insert a .07mm gauge and carefully tighten the adjuster until it lightly pinches the gauge. You should be able to pull the gauge out. Now tighten the lock nut down without rotating the adjuster screw (not easy unless you have 3 hands). If you did it correctly, the .06mm will easly slip in, the 07mm will slip in with a little wiggling and the .08mm will not go. If you can't get a .06mm in there, they are too tight. If you can get a .09mm in, they are too loose.



    Now that you have both the intake and the exhaust valves adjusted, step back and drink a beer It's a good idea to verify your work, so rotate the engine a few times and then check them again. Be patient, you probably won't get it right the first time, I didn't If everything appears to be in good working order, put the bike back together and fire it up. With any luck she will be smooth as silk. If you hear some nasty clacking sounds, immediately shut the bike off and check the valves again.

    I took a quick run around the block and the bike definately responds better and the engine sounde nice and smooth. I will need to take her out for a good thrashing and see if this helps with the stalling issue I have been encountering all along.

    Cheers!
    ChinaV
    Reply With Quote  
     

  2. #2  
    C-Moto Regular volksjagger's Avatar
    Join Date
    Jun 2008
    Posts
    63
    fantastic. thank you for this. i appreciate the effort and attention to detail.

    i beat the hell out of my bike and just had the first valve adjustment done.

    it needed it so bad it was cutting out at top speeds. the carburetor was not the cause.

    valve adjustment is very important but is/was overlooked by many. me included.

    this makes it very clear on how to do it. good werk. thank you again.

    o and ya it is quite "purdy"!!!
    Reply With Quote  
     

  3. #3  
    C-Moto Guru Brice's Avatar
    Join Date
    Apr 2008
    Location
    Xi'an, China
    Posts
    286
    Nice piece of work Lorne.

    I have a 4 cylinders to check for you...
    Reply With Quote  
     

  4. #4  
    C-Moto Regular volksjagger's Avatar
    Join Date
    Jun 2008
    Posts
    63
    well i wanted to update on my comment "it needed it so bad (valve adjustment) it was cutting out at top speeds. the carburetor was not the cause."

    it turns out i had a vacuum problem in the gas tank!!!

    although the bike did like the valve adjustment the stuttering gradually came back.

    after 2 trips to the dealer and about 5 test rides the second time it just needed a vacuum line swapped.

    i went down on my jetting since i went so big on it, all the way to 135. and it amplified the problem. that is when they dug a little deeper and determined it was the vacuum line.

    just wanted to clear this comment up. now it is running like a top again!!!
    Reply With Quote  
     

  5. #5 valve adj 
    C-Moto Noob
    Join Date
    May 2008
    Posts
    2
    Dont forget to rotate engine to set exhaust !!
    Reply With Quote  
     

  6. #6  
    Administrator-tron CrazyCarl's Avatar
    Join Date
    Apr 2008
    Location
    NoVA
    Posts
    2,540
    XS,

    Why would the engine need to be rotated to set the exhaust valve clearances?

    CC
    ---------------------------------------------------
    Subscribe to the hippest, most happeneing Adventure Motorcycle Magazine around!
    Adventure Motorcycle Dual Sport News Magazine

    Help support MCM!! Buy "The Return - Riding Western China" DVD! -

    http://www.motocyclops.com/buydvd/

    Personal China travel info, photo and video site:

    http://www.carlparker.com

    Reply With Quote  
     

  7. #7 Re: QingQi (Qlink) 200GY Illustrated Valve Adjustment 
    C-Moto Not-so-Noob
    Join Date
    Oct 2012
    Location
    Miami, Florida
    Posts
    24
    Quote Originally Posted by volksjagger View Post
    well i wanted to update on my comment "it needed it so bad (valve adjustment) it was cutting out at top speeds. the carburetor was not the cause."

    it turns out i had a vacuum problem in the gas tank!!!

    although the bike did like the valve adjustment the stuttering gradually came back.

    after 2 trips to the dealer and about 5 test rides the second time it just needed a vacuum line swapped.

    i went down on my jetting since i went so big on it, all the way to 135. and it amplified the problem. that is when they dug a little deeper and determined it was the vacuum line.

    just wanted to clear this comment up. now it is running like a top again!!!

    Do you have a picture showing such vaccum line needed to be replaced? I'm have the same issue. I decided to break the rubber seal on the gas cap for a temporary fix which isn't good in the long run because it allows water, moisture, dirt, ect to get into the gas tank.
    Reply With Quote  
     

  8. #8 Re: QingQi (Qlink) 200GY Illustrated Valve Adjustment 
    C-Moto Not-so-Noob
    Join Date
    Oct 2011
    Location
    philippines
    Posts
    12
    Good evening everyone. last sunday i changed my oil and checked the valve as well. this time i tried the .10mm in and .10mm ex. and it feels really better on my bike.
    before i was using .08mm in and .10mm ex. it runs good but the engine comes too hot and it runs no well after a long ride, i mean im not satisfied with the topspeed.
    now the new valve clearance will be tested tomorrow if it will be really better from the old clearance after my long ride.
    Reply With Quote  
     

  9. #9  
    Banned
    Join Date
    Nov 2011
    Location
    fuck off
    Posts
    528
    Quote Originally Posted by modron View Post
    So I went to yamaha dealer and told them to check my valves again. I said to myself that this time i will watch the guy do it. So he unscrew the valve covers and the two little cap. Then he started fiddling around the valves with a spanner. When I asked him if he needed a feeler gauge he laughed and said that he doesnt need it. He explained why but my Chinese isnt good enough to catch everything and the result is that i have no idea why he didnt need that gauge. 15min later the job was done and he said its all good.
    Im a bit confused, is there a way of adjusting the valves without a gauge? My YBR ia a 2012 model so maybe on the newer bikes this problem is solved some other way? I realy have no idea...
    No
    He is a twat Chinese mechanic
    I got laughed at when I borrowed feeler gauges, was told to just lift up n down to get clearance
    Total bullshit
    Once done correctly I had better smoother power and no more hesitations in high rpm
    Buy some do it your self it's no worse then paying a twat to do a bad job
    Reply With Quote  
     

  10. #10 Re: QingQi (Qlink) 200GY Illustrated Valve Adjustment 
    Life Is Good! ChinaV's Avatar
    Join Date
    May 2008
    Location
    Guangdong, China
    Posts
    1,508
    Quote Originally Posted by NZBrakelathes View Post
    No
    He is a twat Chinese mechanic
    I got laughed at when I borrowed feeler gauges, was told to just lift up n down to get clearance
    Total bullshit
    Once done correctly I had better smoother power and no more hesitations in high rpm
    Buy some do it your self it's no worse then paying a twat to do a bad job
    +1

    There are feeler gauges, and then there's the good old Chinese feeler method. I wouldn't want to count on the latter, but I did actually do it one time on a rental bike in Vietnam. Intake was tighter than a new bride so I set it by feel. There's an old saying that too loose is better than too tight, but why risk it.

    BTW, you did sit in the shop all night and wait until morning when the engine was stone cold to adjust the valves... right?

    Cheers!
    Reply With Quote  
     

Page 1 of 2 12 LastLast
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •