Adventure Motorcycle Magazine Subscribe Now

Results 1 to 7 of 7
  1. #1 FINALLY A SOLUTION FOR THE JH600-A/B STALLING 
    Shanghai'ed Shanghaifingers's Avatar
    Join Date
    Jan 2009
    Location
    Shanghai
    Posts
    290
    Ladies and Gentlemen,

    Jialing's factory Representatives where in Shanghai this week and meet with the head of the Black Bats motorcycle club, as a result of their meeting a solution has been discovered to clear up the Jialing 600's stalling issues. We have been all plagued 2 and 3 wheeled a like. We also we under the impression that the ECU (bikes computer) was to blame. However Jialing has stated that the fix to the solution is in simply disconnecting ONE sensor on the top of the cylinder. Now forgive me for not having more details as I just learned this tonight from another rider Shao Mao Aka "Dan the Man".

    Basically on the top of the cylinder cover towards the right side is a sensor (Cam timing or something), simply unhook this sensor unit and tape or seal off the connector. Apparently there is only one sensor on the top of the cylinder cover Why does this help???? Good question! Well apparently these sensor is a redundant unit and the engine has another, I guess a primary unit and its at the lower end of the engine. When these two sensors do not agree (which mechanically they should) the engine cuts out. By eliminating the upper sensor it eliminates this contradiction that can occur thus allowing the engine to run smoothly without interruption.

    Now I am just learning about this less then 2 hrs ago but its such a big thing for us Jialing riders (especially the 2 wheelers) that I had to post it even though I have not done it to my bike (i will do it tomorrow) or have any pictures to help supplement.

    Please anyone with further information post here.....


    Winston
    Reply With Quote  
     

  2. #2 Re: FINALLY A SOLUTION FOR THE JH600-A/B STALLING 
    Banned
    Join Date
    Nov 2011
    Location
    Down the road in China...
    Posts
    1,134
    G'Day,

    Sounds like TIC = This Is China! fix.... makes me laugh very hard and loud over a few cold beers after a great ride out to Suzhou and dinner with mates......
    Reply With Quote  
     

  3. #3 Re: FINALLY A SOLUTION FOR THE JH600-A/B STALLING 
    Senior C-Moto Guru euphonius's Avatar
    Join Date
    Dec 2009
    Location
    mostly Shanghai, sometimes northern California
    Posts
    3,222
    Quote Originally Posted by TB-Racing View Post
    G'Day,

    Sounds like TIC = This Is China! fix.... makes me laugh very hard and loud over a few cold beers after a great ride out to Suzhou and dinner with mates......
    Wait! Did they tell you about the part where you click your heels three times, spin a prayer wheel and chant to yourself, "That wasn't a stall. That wasn't a stall. That wasn't a stall"...

    This alleged fix is just more misinformation, and actually is NOT what came out of the "technicians'" visit. Stay tuned....

    Cheers
    jkp
    Shanghai
    2010 JH600 "Merkin Muffley" (in Shanghai)
    2000 KLR650 "Feezer Ablanalp" (in California)
    Reply With Quote  
     

  4. #4 Re: FINALLY A SOLUTION FOR THE JH600-A/B STALLING 
    Senior C-Moto Guru MJH's Avatar
    Join Date
    May 2010
    Location
    US
    Posts
    5,702
    From what I understand you would have two sensors one on the cam and one on the crank. They are related to firing and timing, however their input is not isolated, that being they are part of a larger calculation formula There should also be a engine temperature sensor and also a presence of detonation sensor.

    Redundant is also called fail safe, disconnecting the circuit is tricking it to either remain open or closed.

    It is supposed to dictate firing and also injection, it is supposed to maintain it within parameters, the problem is or could be the programming or it could be a faulty sensor.

    It could be a fix if the bike operates without that sensor then it s only relying on the position of the crank?
    Reply With Quote  
     

  5. #5 Re: FINALLY A SOLUTION FOR THE JH600-A/B STALLING 
    C-Moto Guru MotoKai's Avatar
    Join Date
    Apr 2010
    Location
    Shanghai
    Posts
    418
    Not sure why we are starting a new thread on this issue - in the essence of housekeeping, please go to: http://www.mychinamoto.com/forums/sh...ll=1#post37432
    _____________________
    嘉陵 JH600-A (Upgraded)
    Reply With Quote  
     

  6. #6 Re: FINALLY A SOLUTION FOR THE JH600-A/B STALLING 
    Danger, Will Robinson! Lao Jia Hou's Avatar
    Join Date
    May 2010
    Location
    Canada/Europe/Asia
    Posts
    1,728
    Quote Originally Posted by Shanghaifingers View Post
    Please anyone with further information post here....
    Here is my reply to Jialing's ridiculous "fix" ... the other thread.
    Reply With Quote  
     

  7. #7 Re: FINALLY A SOLUTION FOR THE JH600-A/B STALLING 
    C-Moto Not-so-Noob Bart Sanders's Avatar
    Join Date
    Aug 2010
    Location
    The Netherlands
    Posts
    23
    Message deleted here, moved to
    Quote Originally Posted by Lao Jia Hou View Post
    Here is my reply to Jialing's ridiculous "fix" ... the other thread.
    Last edited by Bart Sanders; 12-12-2011 at 04:25 PM.
    Reply With Quote  
     

Similar Threads

  1. JH600 stalling
    By milton in forum Maintenance
    Replies: 426
    Last Post: 09-07-2012, 01:18 PM
  2. Finally got a bike in China
    By SHMike in forum Welcome to MCM!
    Replies: 4
    Last Post: 11-05-2010, 09:51 AM
  3. Stalling high rpm qingqi 200gy
    By dacru in forum Maintenance
    Replies: 7
    Last Post: 04-13-2010, 05:44 PM
  4. ChinaV is finally a cover model!!!
    By CrazyCarl in forum Ride, Record, Create
    Replies: 6
    Last Post: 11-16-2009, 09:41 PM
  5. Finally got my ride.
    By iamcanjim in forum Ride Prep and Making Tracks
    Replies: 7
    Last Post: 05-12-2009, 02:22 AM
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •