Thread: loose engine need help
Results 1 to 8 of 8
|
-
#1 loose engine need help
- Join Date
- Dec 2014
- Location
- Houston
- Posts
- 4
12-30-2014, 01:34 AMhello im new to this forum and new to owning a chinese engine and need a little help.
I recently purchased a engine from criaglist it is just the engine from a ATV. its unbranded and the only thing i can find identifying the engine is that its a 167fmm manual clutch 4 forward speeds and reverse. it didnt come with a CDI or wiring harness. did come with a recitifier and carb (thats missing the throttle) All the connectors have been cut from the stator and recitier.
Im not sure were to start, googling 167fmm just brings me to importing site to buy the engine in bulk. if i knew what it was a clone of and what machine/s it would have been in would also be a help. its going into a home built cycle-car.
thanks for the help! i can post pictures if needed.
-
#2 Re: loose engine need help12-30-2014, 07:24 AM
Most "167FMM" are air-cooled CG250. Does it look like http://item.taobao.com/item.htm?id=19602800553 ?
-
#3 Re: loose engine need help
- Join Date
- Dec 2014
- Location
- Houston
- Posts
- 4
-
#4 Re: loose engine need help
- Join Date
- Dec 2014
- Location
- Houston
- Posts
- 4
12-31-2014, 12:41 AMSo what CDI do I need to purchase, and do I even need the rectifier? Or what chinese brands ATVs would this be in so i can buy a harness to make this work.
I'm not sure if i am posting my thread in the right section either, sorry if I'm not.
-
#5 Re: loose engine need help12-31-2014, 03:54 AM
Here is a link to the CDI
http://www.hooperimports.com/product..._id=CDI150-200
you need the rectifier if you intend to use a battery.
http://www.electrosport.com/technica...g-system-works
-
#6 Re: loose engine need help12-31-2014, 04:54 AM
I don't had x-ray vision , so just talking the basics
---
http://www.dansmc.com/electricaltesting.htm
AC-CDI: Most "std" CG family
DC-CDI: Old bike's Source (aka :exciter) coil F***ed or non exist (ALL coil winding are for REC's dc 12v)
---
AC-CDI:
DC-CDI:
S/W is for +12v http://chinariders.net/showthread.php?t=13937
---
Connector is either rectangular ("std" learned from Taiwan) http://www.sanxin.com.cn/exhibit/upl...8522499844.jpg or round (Honda) http://www.sanxin.com.cn/exhibit/upl...5371625487.jpg
---
REC is need for DC 12v … 2 OR 3 wire (In most case are yellow. Sometimes are White or Pink… ) from stator uses different kind...
---
Most vertical chonda are wired like http://do.ejdz.cn:8087/%E6%91%A9%E6%...F%E5%9B%BE.gif
Quad just added some safety S/W from here & there.Last edited by humanbeing; 12-31-2014 at 05:15 AM.
-
#7 Re: loose engine need help
- Join Date
- Dec 2014
- Location
- Houston
- Posts
- 4
01-01-2015, 07:30 PMThanks for the help. Here are some pictures I just took of the engine.
IMG_20150101_130528.jpg
IMG_20150101_130556.jpgIMG_20150101_130556.jpg
And this is what is going into. Its still a work in progress.
IMG_20150101_130812.jpg
-
#8 Re: loose engine need help
- Join Date
- Mar 2013
- Location
- France
- Posts
- 26
02-21-2015, 09:30 PMHello,
I also bought a 167FMM with troubles inside but complete electric system.
Beside of that, electric system is a CG like one with AC ignition system. I have wiring diagram somewhere if you still need;
What about cooling in you system ? Those engines are made for hard work but need cooling.
regards.
fred
« Previous Thread | Next Thread » |
Similar Threads
-
"Loose" front end? Bad suspension?
By Bitteeinbit in forum MaintenanceReplies: 6Last Post: 02-26-2014, 07:16 AM -
dong fang250 bobber has a loose rear spocket
By Tedub in forum StreetReplies: 1Last Post: 06-26-2013, 05:33 AM -
QLink throttle cable loose on carb
By get_out_and_push in forum MaintenanceReplies: 3Last Post: 06-18-2012, 02:37 AM -
chain info - loose ends
By euphonius in forum MaintenanceReplies: 11Last Post: 02-26-2011, 08:44 PM -
Need new engine
By justas696661 in forum Dirt n' Dual-SportReplies: 10Last Post: 01-16-2011, 11:38 PM
Tags for this Thread |
комедии 2024 русские
04-29-2024, 07:03 AM in Off Topic Discussions