Thread: Screw You!!! HELP!
Results 1 to 7 of 7
|
-
#1 Screw You!!! HELP!
- Join Date
- Jul 2015
- Location
- Scotland
- Posts
- 13
11-24-2015, 12:26 AMok so after some damage was taken to my Sinnis Apache 2015, I need to replace a single screw;
The screw lives on the handlebars, right hand side where the plastic square shaped mount is situated for the electric start button & killl switch, the screw hole faces downwards to the ground on the underside of this component and Is about 1cm wide if not a little larger and its a fairly deep hole at 5cm or so, this screw is missing from here and i am unsure as to what screw size goes in the hole!
Now I've just had a look online at CMPO.com and I believe this is the exact screw I need! anyone know for sure?
thanks
-
#2 Re: Screw You!!! HELP!
-
#3 Re: Screw You!!! HELP!
- Join Date
- Jul 2015
- Location
- Scotland
- Posts
- 13
11-24-2015, 10:06 AMahh thanks humanbeing!!
-
#4 Re: Screw You!!! HELP!
- Join Date
- Jul 2015
- Location
- Scotland
- Posts
- 13
11-24-2015, 04:33 PMSo I went out and bought a 5mmx20mm flat screw today and waddya know guys it doesnt fit! not even close!
When I put a screw driver into hole its like 50mm deep and definitely wider than 5mm!!!
back to the drawing board
-
#5 Re: Screw You!!! HELP!11-25-2015, 02:51 AM
can we get some photos of the situation?
Start from distance overview and get closer with two , three detail shots fron various angles.SWM RS500R, R1200GS LC
-
#6 Re: Screw You!!! HELP!
- Join Date
- Sep 2011
- Location
- Sofia, Bulgaria
- Posts
- 262
-
#7 Re: Screw You!!! HELP!
- Join Date
- Jul 2015
- Location
- Scotland
- Posts
- 13
11-30-2015, 12:50 AMJust an update here guys that this issue had been fixed!
Dropped it into a garage as I'd exhausted all ideas I had, mechanic said its usually a small chubby plastic "Cap" that goes in the hole under electric start mount, he had to drill through handlebar with small drillbit and then secure mount on with a small screw, probably just means I may have further issues down the line when I change over to renthal handlebar in new year!
Thanks for help everyone
« Previous Thread | Next Thread » |
Similar Threads
-
Adjusting the Idle Screw
By MatthewHalsey in forum MaintenanceReplies: 2Last Post: 07-06-2015, 10:06 PM -
Pulse Adrenaline unmodified Basic Carb screw settings ?
By Sprocket in forum Dirt n' Dual-SportReplies: 2Last Post: 02-11-2013, 02:04 PM -
Too rich or too lean, which direction to turn the air screw pls?
By Genesequas in forum Parts DeskReplies: 9Last Post: 01-12-2013, 09:42 AM -
air fuel screw pulse adrenaline 125
By pulsepat in forum Modifications (Cosmetic and Performance)Replies: 1Last Post: 07-07-2011, 10:04 PM -
Standard Air/Fuel mixture and Idle screw Settings for a Mikilon M96 125-SB
By da beard in forum MaintenanceReplies: 3Last Post: 10-23-2009, 06:42 PM
комедии 2024 онлайн...
Yesterday, 02:09 AM in Off Topic Discussions