Adventure Motorcycle Magazine Subscribe Now

Results 1 to 3 of 3
  1. #1 lexmoto 125cc problems after problems help needed 
    C-Moto Noob
    Join Date
    May 2016
    Location
    bedford
    Posts
    3
    brought a spare repair lexmoto torando 125 completely rebuilt the engine it had in it at the time as the guy had cooked the pison to point it melted onto the pin and the pin melted onto the crank shaft so i brought a new piston crank shaft barrel and head and gaskests and carb and cdi box put that all together it started nicely but wouldnt go top speed lucky to go over 40 mph 2nd problem is it would miss fire excample driving down the street and all of a sudden sould just drop power i would then decrease power and then gentley put the power back on to get power but even then 50 cc would go faster ...

    so i brought a yibon 125 spare and repair same engine with oil leak replaced the crack seal as someone has used a rage inside the engine to soak up the oil total cowboy job brought crack seal no more oil leak dropped that engine onto the lexmoto same problem so on to engine number 3 engine number 3 had no crab used one the other carbs fired it up on the table rev like a dream dropped that into the big same problem

    the bike has a Immobilise eletric start and a keyfobe start and one them looks like cheap alarm off ebay on it any help ideas apperiated
    Reply With Quote  
     

  2. #2 Re: lexmoto 125cc problems after problems help needed 
    Senior C-Moto Guru humanbeing's Avatar
    Join Date
    Dec 2008
    Posts
    1,509
    3 engines...

    http://www.chinariders.net/showthread.php?t=16179
    Roller/ belt OK?
    Valve in/ex .12mm as Kymco shop manual
    http://forum.jorsindo.com/forum.php?...33&pid=6460309 said...
    ---
    Don't forget it needs air flow as designed for...
    Hidden ??? http://www.motorfans.com.cn/forum.ph...authorid=75082
    Last edited by humanbeing; 05-07-2016 at 12:06 PM.
    Reply With Quote  
     

  3. #3 Re: lexmoto 125cc problems after problems help needed 
    C-Moto Noob
    Join Date
    May 2016
    Location
    bedford
    Posts
    3
    Quote Originally Posted by humanbeing View Post
    3 engines...

    http://www.chinariders.net/showthread.php?t=16179
    Roller/ belt OK?
    Valve in/ex .12mm as Kymco shop manual
    http://forum.jorsindo.com/forum.php?...33&pid=6460309 said...
    ---
    Don't forget it needs air flow as designed for...
    Hidden ??? http://www.motorfans.com.cn/forum.ph...authorid=75082
    yeah rollers and belt is ok been driving it gets up to about 43 mph then dies and then gos again ill check the valves just very stange it gos up to about 40 thats it and then just dies and kicks in
    Reply With Quote  
     

Similar Threads

  1. lexmoto problems
    By clare in forum Maintenance
    Replies: 1
    Last Post: 05-07-2014, 07:46 AM
  2. Lexmoto problems
    By clare in forum Welcome to MCM!
    Replies: 4
    Last Post: 04-29-2014, 12:15 AM
  3. Jinling 21-b problems
    By LewisB08 in forum Maintenance
    Replies: 0
    Last Post: 06-23-2012, 09:52 AM
  4. problems
    By ghost77 in forum Dirt n' Dual-Sport
    Replies: 5
    Last Post: 02-02-2012, 04:08 AM
  5. sprocket problems
    By jape in forum Maintenance
    Replies: 9
    Last Post: 01-22-2011, 01:39 AM
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •