Search:
Type: Posts; User: lagerlout07
Search: Search took 0.00 seconds.
-
05-18-2016, 10:54 PM
Thread: Lexemoto adrenaline electrics dying
by lagerlout07- Replies
- 5
- Views
- 5,142
Re: Lexemoto adrenaline electrics dying
Wd40 down the ignition barrel and turn the key a few times then repeat again for good measure. Make it part of your maintence ritual.
-
05-18-2016, 10:49 PM
Thread: Lexmoto Adrenaline 2015 plate
by lagerlout07- Replies
- 2
- Views
- 5,220
Re: Lexmoto Adrenaline 2015 plate
Your rattle could be a exhaust hum. I have the same engine but a Sinnis vista, my exhaust had another pipe that ran down the inside of the chrome and it used to hum, drove me mental too till I bought...
-
04-03-2016, 11:06 AM
Thread: Keeway RKV 125 (K157FMI) Tuning
by lagerlout07- Replies
- 12
- Views
- 37,553
Re: Keeway RKV 125 (K157FMI) Tuning
No idea with that engine then sorry :)
-
04-03-2016, 12:22 AM
Thread: Keeway RKV 125 (K157FMI) Tuning
by lagerlout07- Replies
- 12
- Views
- 37,553
Re: Keeway RKV 125 (K157FMI) Tuning
Christ where do I start lol
Yes you can get a smaller filter for the crankcase hose. Either fit it to metal stub on the crankcase or put it on the pipe. Depends on room between bottom of the carb.... -
08-26-2015, 12:18 AM
- Replies
- 6
- Views
- 6,342
Re: Engine temperature with stainless steel exhaust
http://www.jba.bc.ca/JBCycle/Resources/jet-chart.jpg
Will help with what and where needs adjusting -
08-26-2015, 12:03 AM
Thread: Mikuni 30mm
by lagerlout07- Replies
- 4
- Views
- 5,189
Re: Mikuni 30mm
Hi
Sorry my reply is abit late i have a k157fmi engine and fitted a mikuni 30mm to it. What i did with the setup was fit my old needle, pilot and main jet rod intonthe 30mm and stuck a 115 jet on... -
05-23-2015, 11:00 PM
Thread: Sinnis blade k157fmi big bore kit
by lagerlout07- Replies
- 2
- Views
- 7,103
Re: Sinnis blade k157fmi big bore kit
I've sent you a pm response to your pm but you will need to upjet. Buy a few different sizes and do a plug chop test to confirm that the bike has the correct mixtures. Youtube is handy for videos on...
-
05-05-2015, 08:53 PM
Thread: k157fmi head bolts
by lagerlout07- Replies
- 3
- Views
- 5,576
Re: k157fmi head bolts
So they are M8, that's OK then.
Thank you very much. -
05-05-2015, 06:37 PM
Thread: k157fmi head bolts
by lagerlout07- Replies
- 3
- Views
- 5,576
k157fmi head bolts
Having a nightmare here so hoping someone can help. Just been doing some maintenance on the bike and removed the head bolts that go threw the engine. I ordered new long bolts but my head nuts are...
-
03-03-2015, 12:00 PM
Thread: K157fmi 150cc Cam Question
by lagerlout07- Replies
- 7
- Views
- 9,641
Re: K157fmi 150cc Cam Question
I ordered the cam of eBay from america, at the time of looking I couldn't find a 250 and now their are a few on their but double what I paid for the 230. I'll defo probably try a 250 at some point...
-
03-02-2015, 04:47 PM
Thread: K157fmi 150cc Cam Question
by lagerlout07- Replies
- 7
- Views
- 9,641
Re: K157fmi 150cc Cam Question
Fitted the Cam, was very easy to fit, difference in the bike is unreal, I've yet to set the carb, I checked the plug and it has gone very rich, no doubt from increased airflow so I'm waiting for a...
-
03-01-2015, 12:52 AM
Thread: K157fmi 150cc Cam Question
by lagerlout07- Replies
- 7
- Views
- 9,641
Re: K157fmi 150cc Cam Question
Hi SanoShaker
Already done that mod back when i fitted my big bore kit. Have actually ordered and its arrived yesterday a CAM SHAFT LT230-S from discussions on this forum. got one cheap so if it... -
02-21-2015, 02:08 AM
- Replies
- 68
- Views
- 122,447
Re: pulse adrenaline 150cc big bore kit fitted
Hi, did same job few months back and had exact same thing.
Buy four new head bolts, a mechanic said they can stress fracture and he would of replaced them. To tighten them in you use two nuts, much... -
02-21-2015, 01:51 AM
Thread: K157fmi 150cc Cam Question
by lagerlout07- Replies
- 7
- Views
- 9,641
K157fmi 150cc Cam Question
Hi,
Had my bore kit fitted for awhile and happy with it, installed a 30mm carb which was a pain to set up but again was another nice boost. But as everyone who does this knows top end power tails... -
04-30-2014, 10:39 PM
- Replies
- 3
- Views
- 9,749
I had this on a sinnis vista. The speedo cable...
I had this on a sinnis vista. The speedo cable had snapped. Yet it still appeared to work perfectly fine. It drove me mad. I took the cable off and pulled gentlly on the inner cable low and behold...
-
04-16-2014, 12:35 AM
Thread: Sinnis Apache gearing?
by lagerlout07- Replies
- 4
- Views
- 11,636
Re: Sinnis Apache gearing?
My sinnis vista is the same. 60 seems tops for me. I have though just fitted a 110 jet and gone for a run today. It makes a considerable difference but I may have jumped abit too far. I fitted a k&m...
-
04-16-2014, 12:28 AM
Thread: cush drive sinnis vista
by lagerlout07- Replies
- 2
- Views
- 5,812
Re: cush drive sinnis vista
Thanks for responding
I had hoped to have ordered one without me dismantling twice. Ill strip it in a few days and have a look ;) -
04-05-2014, 10:19 PM
Thread: cush drive sinnis vista
by lagerlout07- Replies
- 2
- Views
- 5,812
cush drive sinnis vista
Hi
Wondered if anyone had needed to replace there's. Just had my bike serviced and they have flagged it up. But I cant find one for my model specifically which is nothing new. I noticed the... -
10-13-2013, 01:40 PM
Thread: sinnus vista 125
by lagerlout07- Replies
- 5
- Views
- 5,736
Re: sinnus vista 125
Hi
tape idea has worked great dave, will last till new one arrives, thank you so much for the idea. Will at least get me too uni :)
And yes the bike fell to the left, gear shift required... -
10-12-2013, 05:15 PM
Thread: sinnus vista 125
by lagerlout07- Replies
- 5
- Views
- 5,736
sinnus vista 125
Hi folks
After a little help if anyone can, i love this bike and its started giving me a load of problems this last few weeks. I had a nasty fall of it, a bus had broken down and dumped its...
Results 1 to 20 of 20
The Pillars of Salubrity:...
05-12-2024, 12:12 PM in Off Topic Discussions