Results 1,441 to 1,450 of 6336
|
-
#1441 Re: Dong Fang DF 250 RTB Bobber Information12-05-2011, 06:49 PM
around here we have a few radar stations set up..they help you stay the speed on certain rods in certain neighborhoods.They are relatively accurate..I mean i drive the van down them and when it says i am doin 30 I am ..so Ride the bike down them and find I am only like 2 mph off.
but at higher speeds i would not know.. seems to me that when i am doing like 50..on the service roads..it feels like I am standing still compared to traffic.. but then again..most of the time trafiic is NOT doing the speed limit anyway.
-
#1442 Re: Dong Fang DF 250 RTB Bobber Information
- Join Date
- Dec 2011
- Location
- orlando/miami, florida
- Posts
- 72
12-05-2011, 06:54 PMhaha funny, one thing I don't like about these bikes, it feels like I am running the engine too hard at 50mph just trying to get ahead of all the bad drivers around me
2011 250rtc
2004 m3 e46
-
#1443 Re: Dong Fang DF 250 RTB Bobber Information
- Join Date
- Nov 2011
- Location
- calhoun ga
- Posts
- 6
12-06-2011, 07:29 AMwould you guys say this bike is bigger than the honda rebel?? the Honda rebels are way too small...
-
#1444 Re: Dong Fang DF 250 RTB Bobber Information
-
#1445 Re: Dong Fang DF 250 RTB Bobber Information12-06-2011, 01:59 PM
You might try decreasing your rear sprocket size. The DF bobber is geared way too low as it comes from the factory. Don't know about your bike since it is a different model. You need to find a thread about your bike as you are comparing apples and oranges here.
Also don't forget these CG250 engines are really only 229cc, old technology, and don't make a lot of power.Vince
2021 Ural cT
2022 Dong Fang DF250RTG
2021 Ice Bear 150cc scooter
2020 Ice Bear 150cc Scooter
-
#1446 Re: Dong Fang DF 250 RTB Bobber Information
- Join Date
- Aug 2011
- Location
- louisiana
- Posts
- 85
-
#1447 Re: Dong Fang DF 250 RTB Bobber Information
- Join Date
- Nov 2011
- Location
- calhoun ga
- Posts
- 6
12-07-2011, 01:40 AMLove the picture barnone. Looks like a good fit!! Thank you so much for the help my friend, I can honestly say if it wasn't for you id still be unsure about this bike.
-
#1448 Re: Dong Fang DF 250 RTB Bobber Information
-
#1449 Re: Dong Fang DF 250 RTB Bobber Information
- Join Date
- Sep 2011
- Location
- Joliet, IL
- Posts
- 188
12-07-2011, 02:32 AMBarnone, seeing your last photo, have you considered lowering your key/igniition switch lower to the removed EPA equipment bracket? It fits!
-
#1450 Re: Dong Fang DF 250 RTB Bobber Information
- Join Date
- Sep 2011
- Location
- Joliet, IL
- Posts
- 188
12-07-2011, 03:02 AMI changed to a 33T (35T not available at the time & was in a rush), mistake, yes 80mph(indicated & no wind) but a bitch off from stopped. As Barnone suggested 35T is the key if you have flat terraine. Back in this tread, there is a graph for rear sprocket & tire size to establish true max mph.
« Previous Thread | Next Thread » |
Similar Threads
-
Help ID this customized chinese bobber please?
By fonzerelli in forum StreetReplies: 6Last Post: 01-16-2022, 01:39 AM -
DD350E-2 Bobber
By xacarrere in forum Manufacturers and ImportersReplies: 2Last Post: 08-28-2015, 12:03 PM -
Bobber Bikes
By Geronimo in forum SidecarsReplies: 12Last Post: 07-20-2011, 05:02 AM -
my 2nd 16 inch bobber
By Geronimo in forum SidecarsReplies: 3Last Post: 09-13-2010, 11:10 AM -
JH600B Information Wanted
By blazeafar in forum Welcome to MCM!Replies: 1Last Post: 04-29-2008, 12:38 PM
Tags for this Thread |